Toko Jual Shield 16-Channel 12-bit PWM/Servo Harga Murah
Buka 24 Jam , Minggu & Hari Besar Nasional Libur
Beranda » Arduino » Shield » Shield 16-Channel 12-bit PWM/Servo I2C interface – Adafruit

Shield 16-Channel 12-bit PWM/Servo I2C interface – Adafruit

Ditambahkan pada: 1 October 2016 / Kategori:
Kode : A02019
Berat : 0.08 kg
Dilihat : 439 kali
Review : Belum ada review
Rp 299.000
Pesan!
Pesan melalui SMS/WA/BBM/LINE ???
Klik
DISINI !

Bagikan informasi tentang Shield 16-Channel 12-bit PWM/Servo I2C interface – Adafruit kepada teman atau kerabat Anda.

Toko Jual Shield 16-Channel 12-bit PWM/Servo I2C interface – Adafruit Online Harga Murah Grosir/Eceran

Toko Jual Shield 16-Channel 12-bit PWM/Servo I2C interface - Adafruit Harga Murah

Toko Jual Shield 16-Channel 12-bit PWM/Servo I2C interface - Adafruit Harga Murah

There’s an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!

It is 5V compliant, which means you can control it from a 3.3V Arduino and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)

6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs – that’s a lot of servos or LEDs

Adjustable frequency PWM up to about 1.6 KHz

12-bit resolution for each output – for servos, that means about 4us resolution at 60Hz update rate

Configurable push-pull or open-drain output

We wrapped up this lovely chip into a shield with a couple nice extras
-Terminal block for power input (or you can use the 0.1″ breakouts on the side)
-Reverse polarity protection on the terminal block input
-Green and red power-good LEDs
-3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1″ so you can only stack 4 next to each other on 0.1″ header
-Stackable design. You’ll need to pick up stacking headers and right angle 3×4 headers in order to stack on top of this shield without the servo connections getting in the way.
-A spot to place a big capacitor on the V+ line (in case you need it)
-220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
-Solder jumpers for the 6 address select pins
-A lot of extra space remaining? Let’s turn it into a prototyping area. You get a 5×20 proto area for any extra wiring you’d like to add

learn.adafruit.com/adafruit-16-channel-pwm-slash-servo-shield



Kami siap melayani pengiriman barang ke kota-kota besar seluruh INDONESIA, meliputi Jakarta, Depok, Tangerang, Bekasi, Surabaya, Gresik, Bandung, Medan, Semarang, Magelang, Yogyakarta, Surakarta, Solo, Jember, Palembang, Makassar, Batam, Pekanbaru, Bandar Lampung, Malang, Padang, Denpasar Bali, Samarinda, Serang, Banjarmasin, Ujung Pandang, Palangkaraya, Banjarbaru, Bontang, Tasikmalaya, Tarakan, Pontianak, Kendari, Balikpapan, Jambi, Bima, Manado, Mataram NTB, Kupang NTT, Jayapura, Sorong, Ternate, Gorontalo, dll. Dan di kota-kota pelosok yang berada di pulau Sumatera, Jawa, Kalimantan, Sulawesi, Bali, Nusa Tenggara, maupun Papua.

Best Regards,
Toko Jual Komponen Online www.PusatKomponen.com

Produk Terkait Shield 16-Channel 12-bit PWM/Servo I2C interface – Adafruit

Mungkin Anda tertarik dengan produk terbaru kami.

Sidebar Kiri
Kontak
Cart
Sidebar Kanan